Home  »  Manual/Instructions  »  Epson Printer  »  CX5000, CX6000, CX7000, CX7450, CX8400, CX9400f  »  How to install the CISS ,continuous ink supply system into Epson Stylus CX7400 printer

How to install the CISS ,continuous ink supply system into Epson Stylus CX7400 printer

How to install the CISS ,continuous ink supply system into Epson Stylus CX7400 printer
Category: CX5000, CX6000, CX7000, CX7450, CX8400, CX9400f
Posted: 03-17-2010 20:28:00
Views: 6863
Comments: 1 [Read/Post]
Synopsis:

Below is the instruction for Epson CX7400 Printer, but you can use the same technique for CX5000, CX6000, Cx7000, CX7450, CX8400, CX9400f


How to install the CISS ,continuous ink supply system into Epson Stylus CX7400 printer

Below is the instruction for Epson CX7400 Printer, but you can use the same technique for CX5000, CX6000, Cx7000, CX7450, CX8400, CX9400f.

1.Cautions: Thing need to know

  • Find an easy-to-clean place to work when working with ink.
  • Most of the refillable cartridges & the cartridges come with the ciss that have auto reset chips cannot be mixed with original cartridges; the same situation applies for the non-auto reset chip cartridges.
  • Do not use any software and / or chip re setters to reset the chips as it may damage the auto reset chips.
  • During printing do not disturb the external ink tank.
  • Leave the external ink tank at the same level (see picture above).
  • Do not tear off the seal at the bottom of the cartridges.
  • Do not touch or scrape the chips.

    ink tank set up


Prepare Printer

  • Check the printer status to see whether it is normal or not, and check its mechanics for smooth and any damage.
  • Printer a test sheet on the nozzle check to see if any gaps appear on the lines in the printout , Please check your printer manual on information how to printer out the nozzle test page.
  • If the printer show that broken line, do the printer head cleaning till those are good.
  • If the printer is alright then follow the step below for the installation instruction

Note: The ink system will not cause any damage to your printer.


Installation Procedures

A. Place the ink system on the right side of printer. Press ink cartridges change button located on the top of the printer or please check your printermanual for the information on how to replace the cartridges, The cartridges will move to the changing position.

Open the cover locale in front the printer , Remove the original cartridges Unplug the printer So it's easier move the cartridges holder later..

B. Locate the printer Cartridges cover lock. Insert the screwdriver in between the joint and gently remove the lock clip

C. Remove the cartridges holder cover

D. Move the printer head to the left side of the printer

E. Take the cartridges and carefully slide them under the bar as
shown on the right. Rest the cartridges on the side of printer in order to perform the next step.

F. Move the printer head back to the changing cartridge position.Insert cartridges into printer. Place all eight straight down into printer carriage.Starting from left to right, gently press cartridges until cartridges lock into place. Note: The cartridges maybe a little big tight when pressing it down.

G. Attach tubing bridge by removing adhesive protector and then placing it directly across from the arrow or place a little bit to the left of the arrow. See picture on the side.. When placing the tube holder, place it an angle to ensure the tube can freely move without interfering with the cartridge holder.

E. * Move the printer head carriage all the way to the right. Make sure there is enough tubing to allow printer carriage to move freely to the right.
* Do the same move for the cartridges carriage all the way to the left.
* If it appears that the tubing is too short or too long, please make adjustments by sliding the tubing to the desired amount.

Locate the 4 small plugs located on top of the reservoir bottle.
Remove all 4 small plugs that covers the air hole. See picture on the
side. Insert the air filter.

remove the lock...

 

Trouble shooting:

Below are the very common when using the Ciss system

If after install the system and you receive the message the cartridges are not recognize by the printer, Red light flashing...This is he very common problem for the printer that manufactured after 8-2008, Check the link below for the instruction on how to correct that problem

http://www.vtechplace.com/articles/epson-printer/cx5000-cx6000-cx7000-cx7450-cx8400-cx9400f/how-to-reset-the-chips-for-the-ciss-that-dont-have-the-reset-switch-on-top-of-the-cartridges..html

 

Guide to fix the problem with missing color when print http://www.vtechplace.com/articles/epson-printer/common-q-a-for-epson-printer/guide-to-fix-the-problem-with-missing-color-when-print.html

 


Epson CX7400 test Print.

 

Related Items

Ink Refill Set For Epson C68 C88 CX3810 CX6600 CX7800......
Ink Refill Set For Epson C68 C88 CX3810 CX6600 CX7800......


Comments on How to install the CISS ,continuous ink supply system into Epson Stylus CX7400 printer



eliseo dela cruz 04-24-2011 17:03:34
CAN THIS INSTALLATION GUIDE APPLICABLE TO EPSON T-13?


Share comments

Your Name: *
Comments: *
Please Note: HTML Markup will be automatically removed.
The ability to post urls has been disabled by the site administrator.
*
Type the characters you see in the picture:




Apple, Brother, Dell, HP, IBM, Lexmark, Canon, Epson, Xerox and other manufacturer brand names and logos are registered trademarks of their respective owners.
Any and all brand name designations or references are made solely for purposes of demonstrating compatibility.

Welcome to Viet Tech

We aim to make your shopping experience as easy as possible.

Customer satisfaction is our top priority.

Registering a new account is free and only takes a few moments.

Please click here to get started!

Existing Members

Please enter your username and password below...

Forgot Details?

Please enter your email address below...